Installing a Fireplace in NSW: The Approval Nobody Tells You About, and Why You Book in Summer

Share this post

There are three ways to put a fire in a Coffs Harbour living room, and they have three completely different approval paths. One needs council sign off before it goes in. One needs a certificate lodged after. One needs neither.

Almost every conversation about a fireplace installation starts with the appliance and ends with the price. The part in the middle, which is what the law expects of you before anything is bolted to your floor, tends not to come up until somebody is standing in the lounge room with a flue kit.

That is worth fixing, because the rules are genuinely different for wood, gas and electric, and the difference is not a technicality. For one of the three, going ahead without an approval your council does require is an offence under the Act, and it is the property owner who carries it, not the installer. It also comes up years later, when you sell, and a buyer’s solicitor asks for the approval you never applied for.

None of this is difficult. It is just poorly explained, so here is the whole picture in one place.

The short version

  • A wood fireplace installation may need prior approval from council, and whether it does depends on which council you are in. This is the one people miss.
  • A gas fireplace installation needs no council approval, but must be done by a licensed gasfitter and finished with a gas certificate of compliance.
  • An electric fireplace needs no approval and no certificate. It needs a power point.
  • Book in summer. In the cooler months the queue runs four to five weeks.
  • Not sure which path you are on? Call Coffs Gas Company on (02) 6652 2411.

Three fireplaces, three completely different approval paths

This is the table we wish somebody had put in front of us years ago. It is the whole article in one glance.

Type of fireplace Approval needed before install Paperwork afterwards Who is legally allowed to install it
Wood fireplace or wood heater (fixed) Depends on the council. Where it is required, approval under section 68 of the Local Government Act 1993, before the appliance is installed Council may require notification that the work is complete An installer competent to AS/NZS 2918, which is the installation standard for solid fuel appliances
Gas fireplace or gas log fire No council approval Gas certificate of compliance, lodged with Building Commission NSW A licensed gasfitter. Gas work is licensed work in NSW and cannot be done by the homeowner
Electric fireplace or flame fire No None Anyone, for a plug in unit. An electrician if it is hard wired or a new circuit is needed
Portable gas or electric heater No None Anyone. Portable appliances sit outside the approval rules entirely

If you take one thing from this page, take the first row.

The approval nobody tells you about: section 68

Section 68 of the Local Government Act 1993 lists activities that need the prior approval of your local council. It is the same part of the Act that covers things like on site sewage systems and water supply work, which is why almost nobody expects a fireplace to be on the list. It is, at Part F item F4 of the section: install a domestic oil or solid fuel heating appliance, other than a portable appliance.

So a freestanding wood heater, an inbuilt wood fireplace or a slow combustion unit going into an existing masonry chimney all sit inside that item, wherever a council chooses to require the approval.

Here is the part that actually matters locally, and it is the part no buying guide will tell you: not every council does. Across the area we cover the answer changes from one council to the next. Coffs Harbour does not currently require an individual approval for a straightforward compliant installation. Bellingen and Dorrigo do. Bucca has recently dropped the requirement. The approval still exists on the books for the City of Coffs Harbour because the power sits in the Act either way, which is why you will find it listed.

Councils review these policies and they do change, so the only answer worth having is the one for your address on the day. We check it before anything is ordered, and where an approval is needed we submit the application to the council for you.

What council is actually looking at

The application is not a formality but it is not an ordeal either. Council wants to see what the appliance is, where it is going and how it will be flued, which usually means the manufacturer’s specifications and a site plan or sketch showing the position of the flue.

What they are assessing is whether the installation will meet the Building Code and the installation standard, whether the flue terminates high enough and far enough from neighbouring buildings, and whether the position is likely to cause a smoke nuisance for the people next door. That last one is why the topography matters here. A flue that would be fine on a flat block can behave very differently on a hillside in the hinterland where cold air sits in the gully of an evening.

What is exempt

Portable appliances are excluded by the wording of the Act itself. A plug in electric heater, an unflued portable gas heater on a bayonet point, a patio heater: none of those are a fixed solid fuel appliance and none of them need approval.

Some councils in New South Wales also publish a local approvals policy that exempts a compliant solid fuel heater from needing an individual approval where a list of conditions is met, such as flue height and a licensed installer. That varies council by council, so it is worth asking rather than assuming, and it is a conversation we can have with you for your address.

What happens if it is already in and nobody applied

This is more common than you would think, especially with heaters that came with a house. Where a council required an approval, installing a fixed solid fuel appliance without one, or otherwise than in accordance with it, is an offence under the Act.

In practice the issue surfaces at two moments. The first is an insurance claim after a fire, when the insurer asks whether the appliance was approved and compliant. The second is at sale, when a buyer’s solicitor asks for the paperwork. Neither is a good moment to find out. If you have inherited a heater and you do not know its history, the sensible first step is an inspection to see whether it would pass, and we can tell you that in an afternoon.

What a compliant wood fireplace installation actually involves

Approval is the paperwork. This is the physical job, and there are four things that decide whether an installation is right, whichever of our woodfire heaters you settle on.

The appliance has to be legal to sell here in the first place

New South Wales sets minimum standards for new solid fuel heaters. NSW EPA regulations require “at least 60 per cent efficiency and no more than 1.5 grams of particle emissions per kilogram of fuel burnt”.

Efficiency is tested to AS/NZS 4012, emissions to AS/NZS 4013, and a compliant heater carries a plate showing it. That plate is the first thing to look for, and it is the thing that quietly rules out a good deal of what is offered online and second hand. Everything on our showroom floor complies, because it could not legally be sold here otherwise.

The installation standard, and the clearances that come with it

Solid fuel appliances are installed to AS/NZS 2918, the Australian and New Zealand standard for the installation of domestic solid fuel burning appliances. It governs the flue system, how high the flue has to terminate, the floor protection under the appliance and the clearances to anything combustible around it.

Those clearances are the single most common reason a heater cannot go exactly where somebody has pictured it. A timber mantel, a plasterboard return wall, a built in bookshelf, curtains: each one has a required distance, and the heater’s own test data sets it. It is a much better conversation to have before you buy than on install day.

The hearth, and whether your floor will carry it

A fixed wood heater needs non combustible floor protection underneath, sized to the appliance. It also needs a floor that will take the weight, and a wood heater is heavier than people expect, from around 90 kilos for a small unit to roughly 250 for a large one.

On a concrete slab this is a non issue. On a timber floor over joists it sometimes means blocking out and bracing underneath before the appliance arrives, which is a small job when it is planned and an expensive surprise when it is not. Our guide to what a wood heater is made of goes further into weight and floor loading if you want the detail.

The flue, and what salt air does to it up here

The flue is not an accessory. It is the part that makes the appliance work, and on the coast it is also the part that ages fastest. The flue itself is stainless, so it usually outlasts everything, but the rain cap on top takes the brunt of the salt and we replace far more of them in Coffs than we do inland at Dorrigo.

Worth knowing at install time, because a flue run that is easy to reach is a flue that is easy to sweep and easy to re cap later. If you would like to know what happens when that maintenance does not happen, we have written about what happens if you never clean your flue.

Gas fireplace installation: no council approval, but a certificate that matters

A gas fireplace installation does not go anywhere near section 68. What it does involve is licensed work and a document.

Gas work in New South Wales is licensed work as a matter of law rather than good practice. Under the Gas and Electricity (Consumer Safety) Act 2017, all gas installations must be carried out by a licensed gasfitter, and the same NSW Government guidance tells homeowners to “always have a licensed gasfitter install, repair and service gas appliances”. When the job is finished, the gasfitter signs a gas certificate of compliance and lodges it with Building Commission NSW. Keep your copy somewhere you will find it in ten years.

There are two local details that change a gas installation here. The first is that Coffs Harbour has no natural gas network, so every gas appliance in this area runs on LPG, and a unit bought elsewhere may need converting before it can be used. The second is that a modern gas fireplace runs on a power flue that vents through an external wall or up through the roof, so no brick chimney is required. Most of the homes we fit out do not have one.

Our gas fireplaces and gas heaters page covers the brands we carry, the full picture of what we install and certify is on our appliance installation page, and our gasfitting page covers the licensed side of the work. Once the appliance is in, our guide to how often a gas heater should be serviced covers keeping it that way.

Electric fireplace installation: genuinely just a power point

An electric flame fire is the simplest of the three by a wide margin. Nothing is burning, so there is no flue, no chimney, no gas connection, no council approval and no compliance certificate. A plug in or wall mounted unit goes on a standard power point, and you are usually warm the same day it arrives.

The only time a licensed trade is involved is when the unit is hard wired or the room needs a new circuit, which is an electrician’s job rather than ours. Our electric flame fires page covers what we carry, and if you are wondering how much heat one of them will actually give you, we have answered that in do electric fireplaces actually heat a room. If you are still deciding between the three fuels, start with our comparison of a gas fireplace, a wood fireplace and an electric flame fire.

Why you book a fireplace installation in summer

Here is the practical half of the article, and it is the part that saves people the most grief.

Everybody rings in the same week

Every heating business in the region has the same problem. The first genuinely cold week arrives, everybody thinks about their fireplace on the same evening, and the diary fills. Through the cooler months our installation queue typically runs four to five weeks. In summer it does not.

That is not a sales line. It is arithmetic. The work takes the same time in January as it does in June, and there are only so many days in a week.

Approval takes as long as it takes

Where your council requires approval, it is a process with a queue of its own, and it has to be in place before the appliance goes in rather than alongside it. Stacking a council timeframe on top of the installation queue is how a fireplace that was meant to be in by Easter ends up going in around August.

Apply in the warm months and the approval is simply done, sitting in the drawer, ready.

Summer is when the awkward jobs get done properly

The installations that need something extra, a floor braced underneath, a difficult flue run through two storeys, an old masonry chimney checked before an insert goes into it, are much better done when nobody is waiting on heat. There is time to look at it properly, order the right parts and come back if something needs a second visit.

It is also the right time to have an existing flue swept, since we are one of very few businesses around here that sweeps chimneys and flues, and that diary tightens in autumn along with everything else.

How long the actual work takes

Once it is booked, the installation itself is usually shorter than people imagine. A wood heater with a new flue is generally around six hours, so most are done in a day. A straightforward gas fireplace is often quicker. Where the time goes is the preparation, which is exactly why the quoting visit matters more than the install day.

What we look at before we quote

We would rather look at the room than guess from a phone call, and this is what we are checking while we are there.

  • Where the appliance can legally sit, once the clearances to walls, mantels and furnishings are accounted for.
  • What is above the ceiling and through the roof, which decides the flue run and most of the labour.
  • What the floor is made of and whether it needs bracing.
  • Which way the prevailing wind moves across the block, and where the flue will need to terminate.
  • Whether the appliance you are considering is the right output for the space, rather than the one that looked good in the showroom.
  • For gas, where the bottles will live and whether the existing gas line and regulator will carry the appliance at its rated output.

Then you get a number that includes the whole job, which is the only kind of number worth having.

FAQs

Do I need council approval to install a wood fireplace in NSW?

It depends on your council, and that surprises people. Section 68 of the Local Government Act 1993 gives councils the power to require prior approval to install a domestic oil or solid fuel heating appliance other than a portable one, but whether an individual approval is actually needed varies from council to council. Across our area, Coffs Harbour does not currently require one for a compliant installation, while Bellingen and Dorrigo do, and Bucca has recently dropped it. Where approval is required it has to be in place before the appliance goes in rather than afterwards, and we submit the application for you. Councils change these policies, so confirm the position for your address rather than assuming. Portable heaters are exempt everywhere, and gas and electric fireplaces do not require council approval at all.

Do I need approval to install a gas fireplace?

No council approval is required, but the work is licensed. A gas fireplace must be installed by a licensed gasfitter, and the job is completed with a gas certificate of compliance lodged with Building Commission NSW. Keep your copy, because it is what proves the installation was done legally.

Can I install a wood heater myself?

We would not recommend it, and in practice it creates two problems even where it is physically possible. The installation has to comply with AS/NZS 2918 and the Building Code, and council approval is conditional on that compliance, so a self installed appliance that does not meet the standard puts you outside your approval. It also tends to affect insurance. The flue is where most of the risk sits, and it is the part that is easiest to get subtly wrong.

How long does a fireplace installation take?

A wood heater with a new flue is generally around six hours, so most are finished in a day. A straightforward gas fireplace is often quicker, and an electric unit is usually the same day it arrives. The longer part is the lead time rather than the work, particularly in the cooler months when the queue runs four to five weeks.

Can I put a fireplace in a house with no chimney?

Yes, and most of the homes we fit out do not have one. A wood heater runs on its own flue system rather than a masonry chimney. A gas fireplace uses a power flue that vents through an external wall or the roof. An electric fireplace needs nothing at all. If you do have an existing chimney, it can often be used, but it should be inspected first because an old flue is not automatically a usable one.

What if my existing fireplace was installed before I bought the house?

It is worth finding out whether it was approved, because the question tends to arrive at the worst possible time. An inspection will tell you whether the appliance carries a compliance plate, whether the flue and clearances meet the standard, and whether anything needs to change. If it does need work, that is usually a straightforward fix rather than a new appliance.

Is it cheaper to install a fireplace in summer?

The installation itself costs the same. What summer buys you is availability and a properly planned job, because the winter queue disappears, council approval has time to come through, and any preparation work such as bracing a floor or checking an old chimney can be done without anybody waiting on heat.

Who can install a fireplace in Coffs Harbour?

Solid fuel appliances need an installer working to AS/NZS 2918, and gas appliances legally require a licensed gasfitter. Between Jeff and Jay the team covers plumbing, drainage, gasfitting and roofing, which matters more than it sounds, because a flue going through a roof is roofing work and a gas line is gasfitting work. One crew covering both is the difference between one visit and three.

Talk to Us Before You Buy, Not After

The best time to have this conversation is while you are still choosing the appliance, because the room, the floor, the roof and the approval all have a say in what will actually work.

Come and see us at 92 Industrial Drive, North Boambee Valley, call (02) 6652 2411, or send us an enquiry. We will tell you which approval path you are on, what the installation involves at your place and when we can get there. We cover Coffs Harbour, Scotts Head, Dorrigo, Grafton and everywhere in between, and we have been doing it as the same family business since 1982.


Written by the team at Coffs Gas Company.

Disclaimer: This article is general information only and is current at the time of writing. Approval requirements, fees and local approvals policies vary between councils and change over time, and Australian Standards are periodically revised. Confirm the current requirements for your address with your local council, and have any gas or solid fuel appliance installed by an appropriately licensed professional.

[REFERENCES]

Spread the word

Latest Blog Posts

Explore our recent blog posts for valuable information.

The approval you need changes council to council: which path applies to you, and why summer booking saves you weeks.
Regulators say two years, your handbook may say annually: what a service checks, and the signs that mean stop today.
Yes, but not the way you're hoping: what an electric fireplace will actually heat, and who it genuinely suits.

Let Coffs Gas Company Help You Take the Next Step

Put the knowledge you’ve gained into action with the expert services and products from Coffs Gas Company. From reliable heating systems to gas appliance installations, our team is ready to help you create a safer, more efficient space.

Heating

Efficient gas heating solutions to keep your home warm year-round.

Classic woodfire heaters for cosy warmth with a natural ambience.

Stylish electric flame heaters providing warmth and modern aesthetics.

Hot Water Systems

Reliable gas water heating for instant, energy-efficient hot water.

Sustainable solar water heating to reduce energy costs and environmental impact.

Dependable electric water heating for consistent and controlled hot water supply.

Cooking

High-quality cooking appliances designed for efficiency, durability, and convenience.

Premium BBQ appliances for outdoor cooking and entertaining all year round.

Professional installation for safe, efficient operation of gas appliances.

Expert gasfitting services for safe and efficient gas system installations.

Thorough cleaning to ensure safe and efficient chimney operation.

Reliable gas supply solutions for residential and commercial needs.

Expert repairs and servicing to keep your gas appliances in top condition.

Coffs Gas Company is your trusted local gas service provider, delivering quality solutions with expertise.

Stay informed with tips, insights, and the latest updates on gas systems, safety, and maintenance.

Contact

Contact us

We’re here to help with your gas needs.